Manuals.World
Categories

Best Ventilation Hood L3348D manual

Brand: Best, product: Best Ventilation Hood L3348D

Type: Ventilation Hood

Total pages: 2, PDF manual size: 0.58 Mb


CUSTOM HOOD LINER INSTALLATION SHEET
MODELS: L5230, L7030, L7036, L7048, L2936, L2942, L3848, L3854, L3860,
L3336S, L3342S, L4548S, L4554S, L4560S, L3336D,
AND L3348D
PRELIMINARY INSTRUCTIONS
This instruction sheet applies to many liner models, so the illustrations shown are typical ones.
See the table and illustration below to locate your liner choice and use corresponding custom hood base dimensions. For the liner installation, only the bottom of the custom hood is needed. Do not finalize
the entire custom hood yet, because an access is needed for the insert or power pack electrical connection.
WARNING
When building a custom hood for an insert or power pack, always follow all applicable construction codes and standards.
!
LINER MODELS INSERT OR POWER PACK MODELS INSIDE WIDTH (A)
INSIDE DEPTH (B)
WITHOUT BACKBOARD WITH BACKBOARD
L5230 P1951M52CM 28 1/2” 17 1/2” TO 20 1/2” 17 1/8” TO 20 1/8”
L7030 P1951M70CM OR P1952M70CM 28 1/2” 17 1/2” TO 20 1/2” 17 1/8” TO 20 1/8”
L7036 P1951M70CM OR P1952M70CM 34 1/2” 17 1/2” TO 20 1/2” 17 1/8” TO 20 1/8”
L7048 P1951M70CM OR P1952M70CM 46 1/2” 17 1/2” TO 20 1/2” 17 1/8” TO 20 1/8”
L2936 PK2229 34 1/2” 20 1/2” TO 23 1/2” 20 1/8” TO 23 1/8”
L2942 PK2229 40 1/2” 20 1/2” TO 23 1/2” 20 1/8” TO 23 1/8”
L3848 PK2238 OR PKEX2238 46 1/2” 20 1/2” TO 23 1/2” 20 1/8” TO 23 1/8”
L3854 PK2238
OR PKEX2238 52 1/2” 20 1/2” TO 23 1/2” 20 1/8” TO 23 1/8”
L3860 PK2238 OR PKEX2238 58 1/2” 20 1/2” TO 23 1/2” 20 1/8” TO 23 1/8”
L3336D PIK33D 34 1/2” 23 1/2” TO 26 1/2” 23 1/8’ TO 26 1/8’’
L3348D PIK33D 46 1/2” 23 1/2” TO 26 1/2” 23 1/8’ TO 26 1/8’
L3336S PIK33 34 1/2” 22 7/8” TO 25 7/8” 22 1/2” TO 25 1/2”
L3342S PIK33 40 1/2” 22 7/8” TO 25 7/8” 22 1/2” TO 25 1/2”
L4548S PIK45 46 1/2” 22 7/8”
TO 25 7/8” 22 1/2” TO 25 1/2”
L4554S PIK45 52 1/2” 22 7/8”
TO 25 7/8” 22 1/2” TO 25 1/2”
L4560S PIK45 58 1/2” 22 7/8”
TO 25 7/8” 22 1/2” TO 25 1/2”
4''
A
B
HA0015
3/4''
Plywood base thickness: 3/4”
Recommended
thickness:
NOTES: 1. We recommend the base of the custom hood should be 3/4 inch thick plywood. We recommend the sides, front and backboard (if included) of the custom hood to be 3/4“ thick, assuming standard
cabinet widths. The INSIDE DEPTH shown in the table above assumes a minimum cabinet backboard thickness of 3/8’’.
2. If the custom hood base has a backboard, scribe in two (2) 1/2” notches to allow for the side flange extension of the main liner plate, if necessary.
Consider the shape and size of the insert or power pack to determine the configuration of the custom hood. For more details, refer to the installation manual of the insert or power pack.
For custom hood liner detailed installation instructions, see the reverse of this page.
INSTALLATION DU REVÊTEMENT D’ARMOIRE
MODÈLES : L5230, L7030, L7036, L7048, L2936, L2942, L3848, L3854, L3860,
L3336S, L3342S, L4548S, L4554S, L4560S, L3336D ET L3348D
INSTRUCTIONS PRÉLIMINAIRES
Puisque cette feuille d’instruction couvre plusieurs modèles, les illustrations qui s’y trouvent sont typiques.
Afin de déterminer à quelles dimensions d’armoire correspond le revêtement, voir le tableau et l’illustration ci-dessous. Il n’y a que la base de l’armoire qui est nécessaire pour l’installation du revêtement.
Ne pas finaliser l’armoire tout de suite; garder un accès pour le futur branchement électrique du module de hotte encastrable.
AVERTISSEMENT
Toujours suivre tous les codes en vigueur et standards de la construction lors de la construction d’une armoire de module de hotte encastrable.
!
4''
A
B
HA0015
3/4''
Épaisseur du
contreplaqué : 3/4“
NOTES : 1. Nous recommandons que la base de l’armoire soit faite en contreplaqué de 3/4” d’épaisseur. Nous recommandons que l’épaisseur de l’arrière (le cas échéant), de l’avant et des côtés de l’armoire
soit de 3/4”. La PROFONDEUR INTÉRIEURE indiquée dans le tableau ci-dessus sous-entend que l’épaisseur minimale de l’arrière de l’armoire est de 3/8’’.
2. Si la base de l’armoire a un panneau arrière, y faire 2 incisions de 1/2” pour permettre l’insertion des arêtes en coin de la plus grande plaque de revêtement (si nécessaire).
Considérer la forme et la dimension du module de hotte encastrable afin de déterminer la configuration de son armoire. Voir le guide d’installation du module de hotte encastrable pour plus de détails.
Voir le verso de cette page pour les instructions détaillées de l’installation du revêtement d’armoire.
HOJA DE INSTALACIÓN DE LA CUBIERTA DE LA CAMPANA LINER
MODELOS: L5230, L7030, L7036, L7048, L2936, L2942, L3848, L3854, L3860,
L3336S, L3342S, L4548S, L4554S, L4560S, L3336D
Y L3348D
INSTRUCCIONES PRELIMINARES
La presente hoja de instrucciones aplica a muchos modelos, por lo que las ilustraciones que se muestran son las más usuales.
Consulte la tabla y la ilustración que se muestra a continuación para que localice la campana de su elección y utilice la base de dimensiones apropriadas a la campana. Para instalar la cubierta solo
necesitará la parte inferior de la campana. No termine la instalación todavia, ya que necesitará dejar una entrada para la conexión eléctrica.
AVERTANCIA
Siempre que instale una cubierta empotrable con insertos o paquete de potencia, debe seguir todos los codígos y normas de la construcción.
0
!
4''
A
B
HA0015
3/4''
Grueso de madera
laminada: 3/4“
NOTAS: 1. Se recomienda utilizar una base de madera laminada de 3/4” de grueso. Se recomienda que los lados, el frente y de la parte trasera (llegado el caso) de la campana deben tener un grosor
de 3/4”. La PROFUNDIDAD INTERIOR indicada en la tabla arriba supone que el grosor mínimo de la parte trasera del armario es 3/8’’.
2. Si la base de la armario tene una parte trasera, hacer 2 incisíones 1/2” en ella para permitir la insercíon dos aristas en esquina de la placa principal de la cubierta (si es necesario).
Debe tomar en consideración la forma y dimensiones del inserto o del paquete de potencia para determinar la configuración de la campana. Para mayores detalles, refiérase al manual de instalación del
inserto o del paquete de potencia. Para instruccionnes detalladas de la instalación de la cubierta de la campana, vea el reverso de ésta página.
1/2"
HA0014
1/2"
NOTE 1:
NOTE 2:
1/2"
HA0014
1/2"
NOTE 1 :
NOTE 2 :
1/2"
HA0014
1/2"
NOTA 1:
NOTA 2:
MODÈLES MODÈLES DE MODULE DE HOTTE LARGEUR INT. (A)
PROFONDEUR INTÉRIEURE (B)
SANS PANNEAU ARRIÈRE AVEC PANNEAU ARRIÈRE
L5230 P1951M52CM 28 1/2” 17 1/2” À 20 1/2” 17 1/8” À 20 1/8”
L7030 P1951M70CM OU P1952M70CM 28 1/2” 17 1/2” À 20 1/2” 17 1/8” À 20 1/8”
L7036 P1951M70CM OU P1952M70CM 34 1/2” 17 1/2” À 20 1/2” 17 1/8” À 20 1/8”
L7048 P1951M70CM OU P1952M70CM 46 1/2” 17 1/2” À 20 1/2” 17 1/8” À 20 1/8”
L2936 PK2229 34 1/2” 20 1/2” À 23 1/2” 20 1/8” À 23 1/8”
L2942 PK2229 40 1/2” 20 1/2” À 23 1/2” 20 1/8” À 23 1/8”
L3848 PK2238 OU PKEX2238 46 1/2” 20 1/2” À 23 1/2” 20 1/8” À 23 1/8”
L3854 PK2238 OU PKEX2238 52 1/2” 20 1/2” À 23 1/2” 20 1/8” À 23 1/8”
L3860 PK2238 OU PKEX2238 58 1/2” 20 1/2” À 23 1/2” 20 1/8” À 23 1/8”
L3336D PIK33D 34 1/2” 23 1/2” À 26 1/2” 23 1/8’ À 26 1/8’
L3348D PIK33D 46 1/2” 23 1/2” À 26 1/2” 23 1/8’ À 26 1/8’
L3336S PIK33 34 1/2” 22 7/8”
À 25 7/8” 22 1/2” À 25 1/2”
L3342S PIK33 40 1/2” 22 7/8” À 25 7/8” 22 1/2” À 25 1/2”
L4548S PIK45 46 1/2” 22 7/8”
À 25 7/8” 22 1/2” À 25 1/2”
L4554S PIK45 52 1/2” 22 7/8” À 25 7/8” 22 1/2” À 25 1/2”
L4560S PIK45 58 1/2” 22 7/8” À 25 7/8” 22 1/2” À 25 1/2”
MODELOS DE INSERTO O PAQUETE DE POTENCIA ANCHO INT. (A)
PROFUNDIDAD INTERIOR (B)
SIN PARTE TRASERA CON PARTE TRASERA
L5230 P1951M52CM 28 1/2” 17 1/2” A 20 1/2” 17 1/8” A 20 1/8”
L7030 P1951M70CM O P1952M70CM 28 1/2” 17 1/2” A 20 1/2” 17 1/8” A 20 1/8”
L7036 P1951M70CM O P1952M70CM 34 1/2” 17 1/2” A 20 1/2” 17 1/8” A 20 1/8”
L7048 P1951M70CM O P1952M70CM 46 1/2” 17 1/2” A 20 1/2” 17 1/8” A 20 1/8”
L2936 PK2229 34 1/2” 20 1/2” A 23 1/2” 20 1/8” A 23 1/8”
L2942 PK2229 40 1/2” 20 1/2” A 23 1/2” 20 1/8” A 23 1/8”
L3848 PK2238 O PKEX2238 46 1/2” 20 1/2” A 23 1/2” 20 1/8” A 23 1/8”
L3854 PK2238 O PKEX2238 52 1/2” 20 1/2” A 23 1/2” 20 1/8” A 23 1/8”
L3860 PK2238 O PKEX2238 58 1/2” 20 1/2” A 23 1/2” 20 1/8” A 23 1/8”
L3336D PIK33D 34 1/2” 23 1/2” A 26 1/2” 23 1/8’ A 26 1/8’
L3348D PIK33D 46 1/2” 23 1/2” A 26 1/2” 23 1/8’ A 26 1/8’
L3336S PIK33 34 1/2” 22 7/8” A 25 7/8” 22 1/2” A 25 1/2”
L3342S PIK33 40 1/2” 22 7/8” A 25 7/8” 22 1/2” A 25 1/2”
L4548S PIK45 46 1/2” 22 7/8” A 25 7/8” 22 1/2” A 25 1/2”
L4554S PIK45 52 1/2” 22 7/8” A 25 7/8” 22 1/2” A 25 1/2”
L4560S PIK45 58 1/2” 22 7/8”
A 25 7/8” 22 1/2” A 25 1/2”
Épaisseur recommandée :
Grosor recomandado :
BEST by Broan
®
P.O. Box 140, Hartford, WI 53027 1 800 548-0790
BEST by Broan
®
550 boul. Lemire, Drummondville, QC J2C 7W9 1 866 737-7770

check Other guides for Best

Category SubCategory Product name
Kitchen Appliance Ventilation Hood Best Blower IEX42 (1 pages in PDF)
Kitchen Appliance Ventilation Hood Best Blower ILB11 (4 pages in PDF)
Kitchen Appliance Ventilation Hood Best Blower ILB9 (4 pages in PDF)
Kitchen Appliance Ventilation Hood Best Blower IS42 (1 pages in PDF)
Kitchen Appliance Ventilation Hood Best Blower WC26E (44 pages in PDF)
Kitchen Appliance Ventilation Hood Best Microwave Oven UP271 (16 pages in PDF)
Kitchen Appliance Ventilation Hood Best Microwave Oven UP27E (16 pages in PDF)
Kitchen Appliance Ventilation Hood Best Server K30 (32 pages in PDF)
Kitchen Appliance Ventilation Hood Best Universal Remote IS23 (40 pages in PDF)
Kitchen Appliance Ventilation Hood Best Ventilation Hood BER02IS (1 pages in PDF)

Best is a well-known distributer selling various equipment including computer equipment. We count 59 rare docs of this distributer . Now you're reading a user guide for Best Ventilation Hood L3348D.


This manual is encoded in PDF file format

The PDF (Portable Document Format) was created in the early 1990’s as a brand new way for computer users to share documents between each other, especially if one person has a PC and the other a Mac. The shared PDF will display exactly the same on both computers.

PDF was created by Adobe and is no maintained by the International Organisation for Standardisation (ISO). It is a very interactive format and can contain buttons, links, audio, video, form fields, business logic and even electronic signatures. It can capture fonts, images as well as document texts and can also format documents from many different programs.

Most PDF viewers or the software used to view the PDF is provided free of charge. There are many options available including Scribus, pdfTex, Adobe InDesign, Adobe Illustrator as well as Google Docs. The most popular however is Acrobat Reader DC.

Why we provide Best Ventilation Hood manuals in PDF?:

  • · PDF’s are incredibly convenient and are easy to open and read by everyone, regardless of whether they have a PC or Mac.
  • · A PDF can be compressed into a file size that is easy to email while still maintaining the quality of the images.
  • · A PDF file can be made incredibly secure as you can set up passwords, digital signatures and even watermarks.
  • · A PDF allows you input many different types of content including images, animations, 3D models, hyperlinks and buttons.

PDF’s do have their drawbacks such as:

  • · PDF’s can often be difficult to edit or to extract information from as it’s original intention was to make the exchange of documents easier.
  • · There are different types of PDF’s, especially when searching or extracting information.

If you have a document that you would like to convert into a PDF, there are many sites online that will do the conversion for you for free and very quickly. The same is true if you are looking to convert from PDF format into a different format. This is often a much easier way to edit a PDF.

PDF size: 593.92 KB
Other Best manuals