Audio-Technica Headphones AT892 manual

Brand: Audio-Technica, product: Audio-Technica Headphones AT892

Type: Headphones

Total pages: 1, PDF manual size: 0.11 Mb

Lightweight microminiature headset with ergonomic under-ear design
Exceptional sound quality and rugged construction
Adjustable fit for left or right ear
Flexible performance as a wired or wireless microphone - Use with
included power module or with any Audio-Technica UniPak
Available in black, cocoa (-CO) and beige (-TH) models
With a capsule diameter of just 2.5 mm, the AT892 MicroSet provides the
ultimate in low-profile, high-performance audio. This omnidirectional
condenser microminiature headworn mic offers an ergonomic under-ear
design: its flexible, lightweight contoured loop hooks behind the ear for an
ultra-secure, comfortable fit with or without glasses.
The AT892 MicroSet's flexible design
enables it to be worn on either the left
or right ear. Position the lightweight
contoured loop around the back of your
ear, so that the boom extends from the
bottom of your ear as shown. Bend the
loop as needed to achieve a secure,
comfortable fit, so that the MicroSet is not
dislodged by shaking your head. Remove
the MicroSet and bend a gentle curve in
the microphone's boom. Hook the
MicroSet back around your ear, and adjust
the boom as needed to follow the contour
of your face, positioning the microphone
near the corner of your mouth. MicroSet
has a large acoustical sweet spot; experiment
with placement near the corner of your
mouth for optimal performance.
A cable clip is provided for strain relief, allowing the MicroSet to remain
securely in place without the weight of the cable pulling on the headset. To
install the cable clip, slip the cable into the snap-on connector and attach the
clip to clothing, leaving enough slack on the MicroSet side of the clip to allow
for free, comfortable motion.
The donut-shaped moisture guard is provided to protect the element from
sweat and moisture. Position the moisture guard as close to the element as
possible to provide maximum protection. To remove the moisture guard, first
remove the element cover and place it out of harm's way. Gently slide the
moisture guard over the element. Replace the element cover.
The AT892 is intended for use in professional applications where remote
power is available. It requires 11V to 52V DC phantom power, which may be
provided by a mixer or console, or by a separate, in-line source such as the
Audio-Technica AT8801 single-channel or CP8506 four-channel phantom
power supplies. The cable is terminated with a locking 4-pin connector for use
with the included AT8539 power module, as well as with all Audio-Technica
body-pack wireless transmitters.
Output from the power module's XLRM-type connector is low impedance
(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground
(shield). Output phase is “Pin 2 hot” – positive acoustic pressure produces
positive voltage at Pin 2.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
P51750 ©2007 Audio-Technica U.S., Inc. Printed in U.S.A.
AT892 MicroSet
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Omnidirectional
LOW FREQUENCY ROLL-OFF 80 Hz, 18 dB/octave
OPEN CIRCUIT SENSITIVITY –44 dB (6.3 mV) re 1V at 1 Pa*
IMPEDANCE 250 ohms
DYNAMIC RANGE (typical) 88 dB, 1 kHz at Max SPL
60 dB, 1 kHz at 1 Pa*
2.4 g (0.08 oz)
POWER MODULE 85 g (3.0 oz)
8.1 mm (0.32") long,
2.7 mm (0.11") diameter
BOOM 98.4 mm (3.87") long,
1.07 mm (0.042") boom diameter
POWER MODULE 97.6 mm (3.84") long,
18.9 mm (0.74") diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
(power module)
CABLE 1.4 m (55") long (permanently
attached to microphone) 1.6 mm
(0.06") diameter, 2-conductor
shielded cable with locking 4-pin
ACCESSORIES FURNISHED AT8539 power module; two AT8157
windscreens; two AT8156 element
covers; AT8440 clothing clip;
moisture guard; belt clip;
carrying case
Specifications derived by using AT8539 power module. In the interest of standards
development, A.T.U.S. offers full details on its test methods to other industry professionals
on request.
*1 Pascal = 10 dynes /cm
= 10 microbars = 94 dB SPL
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
Function Wire Color
Pin 1 Ground/Shield Green
Pin 2 Instrument Jumper to Pin 1
Pin 3 Mic Audio Copper Color
Pin 4 Bias + In  Red
8 kHz
Polar Pattern
200 Hz
1 kHz
5 kHz
Frequency in Hertz
12" or more on axis
Frequency Response
Response in dB

check Other guides for Audio-Technica

Category SubCategory Product name
Home Audio Headphones Audio-Technica Battery Charger ATW-CHG2 (2 pages in PDF)
Home Audio Headphones Audio-Technica DJ Equipment AT-MX351 (15 pages in PDF)
Home Audio Headphones Audio-Technica DJ Equipment AT-MX381 (11 pages in PDF)
Home Audio Headphones Audio-Technica DVR U857QLU (1 pages in PDF)
Home Audio Headphones Audio-Technica DVR U857QU (1 pages in PDF)
Home Audio Headphones Audio-Technica Headphones at2020 usb (23 pages in PDF)
Home Audio Headphones Audio-Technica Headphones AT803 (1 pages in PDF)
Home Audio Headphones Audio-Technica Headphones AT831R (2 pages in PDF)
Home Audio Headphones Audio-Technica Headphones AT892 (1 pages in PDF)
Home Audio Headphones Audio-Technica Headphones ATH-ANC27 (2 pages in PDF)

Audio-Technica is a well-known supplier selling different equipment related to communications. In our library we have 121 free user guides related to this company . Now you're reading a user guide for Audio-Technica Headphones AT892.

This manual is encoded in PDF file format

The PDF (Portable Document Format) was created in the early 1990’s as a brand new way for computer users to share documents between each other, especially if one person has a PC and the other a Mac. The shared PDF will display exactly the same on both computers.

PDF was created by Adobe and is no maintained by the International Organisation for Standardisation (ISO). It is a very interactive format and can contain buttons, links, audio, video, form fields, business logic and even electronic signatures. It can capture fonts, images as well as document texts and can also format documents from many different programs.

Most PDF viewers or the software used to view the PDF is provided free of charge. There are many options available including Scribus, pdfTex, Adobe InDesign, Adobe Illustrator as well as Google Docs. The most popular however is Acrobat Reader DC.

Why we provide Audio-Technica Headphones manuals in PDF?:

  • · PDF’s are incredibly convenient and are easy to open and read by everyone, regardless of whether they have a PC or Mac.
  • · A PDF can be compressed into a file size that is easy to email while still maintaining the quality of the images.
  • · A PDF file can be made incredibly secure as you can set up passwords, digital signatures and even watermarks.
  • · A PDF allows you input many different types of content including images, animations, 3D models, hyperlinks and buttons.

PDF’s do have their drawbacks such as:

  • · PDF’s can often be difficult to edit or to extract information from as it’s original intention was to make the exchange of documents easier.
  • · There are different types of PDF’s, especially when searching or extracting information.

If you have a document that you would like to convert into a PDF, there are many sites online that will do the conversion for you for free and very quickly. The same is true if you are looking to convert from PDF format into a different format. This is often a much easier way to edit a PDF.

PDF size: 112.64 KB
Other Audio-Technica manuals