3Com Drums 3C17121 manual

Brand: 3Com, product: 3Com Drums 3C17121

Type: Drums

Total pages: 6, PDF manual size: 0.82 Mb

WARNING: Installation and removal of the Module must
be carried out by qualified personnel only. Before
installing the Module into a unit, you must first
disconnect the unit from the mains power supply. For
full safety instructions, refer to the user guide that
accompanies the unit.
AVERTISSEMENT: Confiez l'installation et la dépose de
ce Module à un personnel qualifié. Avant d'installer ce
Module dans un groupe, vous devez au préalable
débrancher ce groupe de l'alimentation secteur. Pour
prendre connaissance des consignes complètes de
sécurité, consultez le guide utilisateur qui accompagne
ce groupe.
WARNHINWEIS: Die Installation und der Ausbau des
Moduls darf nur durch Fachpersonal erfolgen. Vor dem
Installieren des Moduls in einem Gerät muß zuerst der
Netzstecker des Geräts abgezogen werden. Vollständige
Sicherheitsanweisungen sind dem Benutzerhandbuch des
Gets zu entnehmen.
WARNING: When the Module is inserted into the
switch, the captive screws securing the Module must be
tightened with a suitable tool. Keep the blanking plate
and the fixings in a safe place. If you remove the
Module at any time, you must then replace the blanking
AVERTISSEMENT: Quand le Module est inséré dans le
commutateur, visser le module, en le securisant
fortemant avec un outil adapté. Conservez la plaque
d'obturation et les fixations en lieu sûr. Si vous retirez le
Module à tout instant, vous devez alors replacer la
plaque d'obturation.
WARNHINWEIS: Beim Einsetzen des Moduls in dem
Switch sind die unverlierbaren Schrauben mit einem
passenden Werkzeug festzuziehen. Die Distanzplatte und
die Befestigungselemente an einem sicheren Ort
aufbewahren. Beim Austausch des Moduls ist auch die
Distanzplatte zu ersetzen.
WARNING: RJ-45 Ports. These are shielded RJ-45 data
sockets. They cannot be used as standard traditional
telephone sockets, or to connect the unit to a traditional
PBX or public telephone network. Only connect RJ-45
data connectors, network telephony systems, or network
telephones to these sockets.
Either shielded or unshielded data cables with shielded
or unshielded jackets can be connected to these data
AVERTISSEMENT: Points d’accès RJ-45. Ceux-ci sont
protégés par des prises de données. Ils ne peuvent pas
être utilisés comme prises de téléphone conventionnelles
standard, ni pour la connection de l’unité à un réseau
téléphonique central privé ou public. Raccorder
seulement connecteurs de données RJ-45, systèmes de
réseaux de téléphonie ou téléphones de réseaux à ces
Il est possible de raccorder des câbles protégés ou non
protégés avec des jacks protégés ou non protégés à ces
prises de don
WARNHINWEIS: RJ-45-Porte. Diese Porte sind
geschützte Datensteckdosen. Sie dürfen weder wie
normale traditionelle Telefonsteckdosen noch für die
Verbindung der Einheit mit einem traditionellem
privatem oder öffentlichem Telefonnetzwerk gebraucht
werden. Nur RJ-45-Datenanscluße, Telefonnetzsysteme
or Netztelefone an diese Steckdosen anschließen.
Entweder geschützte oder ungeschützte Buchsen dürfen
an diese Datensteckdosen angeschlossen werden.
Handling the Module
The Module can be easily damaged by electrostatic
discharge. To prevent damage, observe the following:
Always wear an anti-static wristband connected to a
suitable earth point.
Do not remove the Module from its packaging until
you are ready to install it into a Switch.
Do not touch any of the pins, connections or
components on the Module.
Handle the Module only by its edges and front panel.
Always store or transport the Module in anti-static
Installing the Module into a Switch
CAUTION: This Module is not hot-swappable. Always
make sure that the Switch is powered down and
disconnected from the mains before installing or
removing a Module. Use the following instructions when
installing or removing a Module.
To install the Module:
Ensure that the Switch is disconnected from the mains
power supply and that you are wearing an anti-static
wristband connected to a suitable earth point.
Undo the two screws securing the blanking plate at the
rear of the Switch using a suitable screwdriver. Do not
remove any other screws from the rear of the Switch.
Remove the blanking plate.
Hold the Module so that the text on the front panel is
upright and insert it into the Switch, ensuring the
connectors are fully engaged (see Figure 1
). Make sure
the Module is pushed fully in.
Secure the Module by tightening the two captive screws
with a screwdriver.
Keep the blanking plate in a safe place. If you remove
the Module at any time, you must replace the blanking
plate to prevent dust and debris entering the Switch.
Replacing the blanking plate will also help circulate
cooling air through the Switch.
Each Switch has the facility to accept up to two
Expansion Modules, allowing Gigabit Ethernet or Fast
Ethernet connections. Modules can be inserted into
either Expansion Module slot.
Figure 1
Inserting the Module into the Switch

check Other guides for 3Com

Category SubCategory Product name
Musical Instruments & Equipment Drums 3Com Baby Gym 2580 (6 pages in PDF)
Musical Instruments & Equipment Drums 3Com Cable Box 3CR856-95 (2 pages in PDF)
Musical Instruments & Equipment Drums 3Com Cell Phone 3C10408A (74 pages in PDF)
Musical Instruments & Equipment Drums 3Com Chainsaw Sharpener L1 (20 pages in PDF)
Musical Instruments & Equipment Drums 3Com Coffeemaker E-10 (2 pages in PDF)
Musical Instruments & Equipment Drums 3Com Coffeemaker SP-510UZ (1 pages in PDF)
Musical Instruments & Equipment Drums 3Com Computer Accessories 900-0387-01 (28 pages in PDF)
Musical Instruments & Equipment Drums 3Com Computer Hardware 3CB9EF (12 pages in PDF)
Musical Instruments & Equipment Drums 3Com Computer Hardware 5000 ATM (114 pages in PDF)
Musical Instruments & Equipment Drums 3Com Computer Hardware DK8X (64 pages in PDF)

3Com is a famous supplier that produce different devices such as baby. We count 320 original user manuals related to this company . Now you're reading a user guide for 3Com Drums 3C17121.

This manual is encoded in PDF file format

The PDF (Portable Document Format) was created in the early 1990’s as a brand new way for computer users to share documents between each other, especially if one person has a PC and the other a Mac. The shared PDF will display exactly the same on both computers.

PDF was created by Adobe and is no maintained by the International Organisation for Standardisation (ISO). It is a very interactive format and can contain buttons, links, audio, video, form fields, business logic and even electronic signatures. It can capture fonts, images as well as document texts and can also format documents from many different programs.

Most PDF viewers or the software used to view the PDF is provided free of charge. There are many options available including Scribus, pdfTex, Adobe InDesign, Adobe Illustrator as well as Google Docs. The most popular however is Acrobat Reader DC.

Why we provide 3Com Drums manuals in PDF?:

  • · PDF’s are incredibly convenient and are easy to open and read by everyone, regardless of whether they have a PC or Mac.
  • · A PDF can be compressed into a file size that is easy to email while still maintaining the quality of the images.
  • · A PDF file can be made incredibly secure as you can set up passwords, digital signatures and even watermarks.
  • · A PDF allows you input many different types of content including images, animations, 3D models, hyperlinks and buttons.

PDF’s do have their drawbacks such as:

  • · PDF’s can often be difficult to edit or to extract information from as it’s original intention was to make the exchange of documents easier.
  • · There are different types of PDF’s, especially when searching or extracting information.

If you have a document that you would like to convert into a PDF, there are many sites online that will do the conversion for you for free and very quickly. The same is true if you are looking to convert from PDF format into a different format. This is often a much easier way to edit a PDF.

PDF size: 839.68 KB
Other 3Com manuals